All commands (14,187)

What's this?

commandlinefu.com is the place to record those command-line gems that you return to again and again. That way others can gain from your CLI wisdom and you from theirs too. All commands can be commented on, discussed and voted up or down.

Share Your Commands


Check These Out

Get AWS temporary credentials ready to export based on a MFA virtual appliance
You might want to secure your AWS operations requiring to use a MFA token. But then to use API or tools, you need to pass credentials generated with a MFA token. This commands asks you for the MFA code and retrieves these credentials using AWS Cli. To print the exports, you can use: `awk '{ print "export AWS_ACCESS_KEY_ID=\"" $1 "\"\n" "export AWS_SECRET_ACCESS_KEY=\"" $2 "\"\n" "export AWS_SESSION_TOKEN=\"" $3 "\"" }'` You must adapt the command line to include: * $MFA_IDis ARN of the virtual MFA or serial number of the physical one * TTL for the credentials

Takes and displays screenshot of Android phone over adb.
Dependencies on phone: adb access, screencap command, base64 command. Dependencies on computer: adb, sed, base64, display (from imagemagick, but can substitute other image viewer which reads from stdin). This should work around adb stupidies (i.e. that it replaces \n with \r\n) with base64.

Get playlist for Livestream on YouTube

Clean up display when the bash prompt is displayed
This will cause bash to fix a garbled terminal before the prompt is printed. For example, if you cat a file with nonprintable character sequences, the terminal sometimes ends up in a mode where it only prints line drawing characters. This sequence will return the terminal to the standard character set after every command.

Get the Volume labels all bitlocker volumes had before being encrypted
Get information of volume labels of bitlocker volumes, even if they are encrypted and locked (no access to filesystem, no password provided). Note that the volume labels can have spaces, but only if you name then before encryption. Renaming a bitlocker partition after being encrypted does not have the same effect as doing it before.

Encrypted archive with openssl and tar
command to decrypt: $ openssl enc -aes-256-cbc -d < secret.tar.enc | tar x Of course, don't forget to rm the original files ;) You may also want to look at the openssl docs for more options.

Redirect incoming traffic to SSH, from a port of your choosing
Stuck behind a restrictive firewall at work, but really jonesing to putty home to your linux box for some colossal cave? Goodness knows I was...but the firewall at work blocked all outbound connections except for ports 80 and 443. (Those were wide open for outbound connections.) So now I putty over port 443 and have my linux box redirect it to port 22 (the SSH port) before it routes it internally. So, my specific command would be: $iptables -t nat -A PREROUTING -p tcp --dport 443 -j REDIRECT --to-ports 22 Note that I use -A to append this command to the end of the chain. You could replace that with -I to insert it at the beginning (or at a specific rulenum). My linux box is running slackware, with a kernel from circa 2001. Hopefully the mechanics of iptables haven't changed since then. The command is untested under any other distros or less outdated kernels. Of course, the command should be easy enough to adapt to whatever service on your linux box you're trying to reach by changing the numbers (and possibly changing tcp to udp, or whatever). Between putty and psftp, however, I'm good to go for hours of time-killing.

Which processes are listening on a specific port (e.g. port 80)
swap out "80" for your port of interest. Can use port number or named ports e.g. "http"

Shows the torrent file name along with the trackers url
Replace * with any filename matching glob or an individual filename

Convert seconds to [DD:][HH:]MM:SS
Converts any number of seconds into days, hours, minutes and seconds. sec2dhms() { declare -i SS="$1" D=$(( SS / 86400 )) H=$(( SS % 86400 / 3600 )) M=$(( SS % 3600 / 60 )) S=$(( SS % 60 )) [ "$D" -gt 0 ] && echo -n "${D}:" [ "$H" -gt 0 ] && printf "%02g:" "$H" printf "%02g:%02g\n" "$M" "$S" }


Stay in the loop…

Follow the Tweets.

Every new command is wrapped in a tweet and posted to Twitter. Following the stream is a great way of staying abreast of the latest commands. For the more discerning, there are Twitter accounts for commands that get a minimum of 3 and 10 votes - that way only the great commands get tweeted.

» http://twitter.com/commandlinefu
» http://twitter.com/commandlinefu3
» http://twitter.com/commandlinefu10

Subscribe to the feeds.

Use your favourite RSS aggregator to stay in touch with the latest commands. There are feeds mirroring the 3 Twitter streams as well as for virtually every other subset (users, tags, functions,…):

Subscribe to the feed for: