Commands by sqweek (1)

  • Monitors battery usage (rate of energy charge/discharge)

    Needs to be run in a battery sysfs dir, eg. /sys/class/power_supply/BAT0 on my system. Displays the battery's current charge and the rate per-second at which energy is {dis,}charging. All values are displayed as percentages of "full" charge. The first column is the current charge. The second is the rate of change averaged over the entire lifetime of the command (or since the AC cable was {un,}plugged), and the third column is the rate of change averaged over the last minute (controlled by the C=60 variable passed to awk). The sample output captures a scenario where I ran 'yes' in another terminal to max out a CPU. My battery was at 76% charge and you can see the energy drain starts to rise above 0.01% per-second as the cpu starts working and the fan kicks in etc. While idle it was more like 0.005% per-second. I tried to use this to estimate the remaining battery life/time until fully charged, but found it to be pretty useless... As my battery gets more charged it starts to charge slower, which meant the estimate was always wrong. Not sure if that's common for batteries or not. Show Sample Output


    -1
    while cat energy_now; do sleep 1; done |awk -v F=$(cat energy_full) -v C=60 'NR==1{P=B=$1;p=100/F} {d=$1-P; if(d!=0&&d*D<=0){D=d;n=1;A[0]=B=P}; if(n>0){r=g=($1-B)/n;if(n>C){r=($1-A[n%C])/C}}; A[n++%C]=P=$1; printf "%3d %+09.5f %+09.5f\n", p*$1, p*g, p*r}'
    sqweek · 2015-09-19 15:45:40 11

What's this?

commandlinefu.com is the place to record those command-line gems that you return to again and again. That way others can gain from your CLI wisdom and you from theirs too. All commands can be commented on, discussed and voted up or down.

Share Your Commands

Check These Out

Top ten (or whatever) memory utilizing processes (with children aggregate) - Can be done without the multi-dimensional array

Show apps that use internet connection at the moment.
show only the name of the apps that are using internet

Find out how much ram memory has your video (graphic) card

External IP (raw data)

Which processes are listening on a specific port (e.g. port 80)
swap out "80" for your port of interest. Can use port number or named ports e.g. "http"

Does a traceroute. Lookup and display the network or AS names and AS numbers.
From the man page. lft ? display the route packets take to a network host/socket using one of several layer-4 protocols and methods; optionally show heuristic network information in transitu -A Enable lookup and display of of AS (autonomous system) numbers (e.g., [1]). This option queries one of several whois servers (see options 'C' and 'r') in order to ascertain the origin ASN of the IP address in question. By default, LFT uses the pWhoIs service whose ASN data tends to be more accurate and more timely than using the RADB as it is derived from the Internet's global routing table. -N Enable lookup and display of network or AS names (e.g., [GNTY-NETBLK-4]). This option queries Prefix WhoIs, RIPE NCC, or the RADB (as requested). In the case of Prefix WhoIs or RADB, the network name is displayed. In the case of RIPE NCC, the AS name is displayed.

HTTP GET request on wireshark remotly

True Random Dice Roll

cycle through everything sox knows how to read, playing only the first three seconds
I wasted two hours reading the sox documentation and searching on the web for the format of some obscure fscking sound sample, and then finally came up with this. This plays only the first three seconds of your unknown formatted sound file using every one of sox's built-in filetypes. If you don't get an exact match, you may get close. . I could not fit every single type in and keep it under 127 characters, so you will have to replace "..." with the full list obtainable by `$ sox --help` (or try `Show sample output`) . note: /usr/bin/play should be linked to sox on most systems.

kill all foo process
Kill all processes with foo in them. Similar to pkill but more complete and also works when there is no pkill command. Works on almost every Linux/Unix platform I have tried.

Stay in the loop…

Follow the Tweets.

Every new command is wrapped in a tweet and posted to Twitter. Following the stream is a great way of staying abreast of the latest commands. For the more discerning, there are Twitter accounts for commands that get a minimum of 3 and 10 votes - that way only the great commands get tweeted.

» http://twitter.com/commandlinefu
» http://twitter.com/commandlinefu3
» http://twitter.com/commandlinefu10

Subscribe to the feeds.

Use your favourite RSS aggregator to stay in touch with the latest commands. There are feeds mirroring the 3 Twitter streams as well as for virtually every other subset (users, tags, functions,…):

Subscribe to the feed for: