Commands by cmbowyer13 (0)

  • bash: commands not found

What's this?

commandlinefu.com is the place to record those command-line gems that you return to again and again. That way others can gain from your CLI wisdom and you from theirs too. All commands can be commented on, discussed and voted up or down.

Share Your Commands


Check These Out

TCP and UDP listening sockets
This command show listening sockets TCP and UDP. Useful for stop unwanted services from linux.

Create the four oauth keys required for a Twitter stream feed
Twitter stream feeds now require authentication. This command is the FIRST in a set of five commands you'll need to get Twitter authorization for your final Twitter command. *** IMPORTANT *** Before you start, you have to get some authorization info for your "app" from Twitter. Carefully follow the instructions below: Go to dev.twitter.com/apps and choose "Create a new application". Fill in the form. You can pick any name for your app. After submitting, click on "Create my access token". Keep the resulting page open, as you'll need information from it below. If you closed the page, or want to get back to it in the future, just go to dev.twitter.com/apps Now customize FIVE THINGS on the command line as follows: 1. Replace the string "Consumer key" by copying & pasting your custom consumer key from the Twitter apps page. 2. Replace the string "Consumer secret" by copying & pasting your consumer secret from the Twitter apps page. 3. Replace the string "Access token" by copying & pasting your access token from the Twitter apps page. 4. Replace string "Access token secret" by copying & pasting your own token secret from the Twitter apps page. 5. Replace the string 19258798 with the Twitter UserID NUMBER (this is **NOT** the normal Twitter NAME of the user you want the tweet feed from. If you don't know the UserID number, head over to www.idfromuser.com and type in the user's regular Twitter name. The site will return their Twitter UserID number to you. 19258798 is the Twitter UserID for commandlinefu, so if you don't change that, you'll receive commandlinefu tweets, uhm... on the commandline :) Congratulations! You're done creating all the keys! Environment variables k1, k2, k3, and k4 now hold the four Twitter keys you will need for your next step. The variables should really have been named better, e.g. "Consumer_key", but in later commands the 256-character limit forced me to use short, unclear names here. Just remember k stands for "key". Again, remember, you can always review your requested Twitter keys at dev.twitter.com/apps. Our command line also creates four additional environment variables that are needed in the oauth process: "once", "ts", "hmac" and "id". "once" is a random number used only once that is part of the oauth procedure. HMAC is the actual key that will be used later for signing the base string. "ts" is a timestamp in the Posix time format. The last variable (id) is the user id number of the Twitter user you want to get feeds from. Note that id is ***NOT*** the twitter name, if you didn't know that, see www.idfromuser.com If you want to learn more about oauth authentication, visit oauth.net and/or go to dev.twitter.com/apps, click on any of your apps and then click on "Oauth tool" Now go look at my next command, i.e. step2, to see what happens next to these eight variables.

Poor man's nmap for a class C network from rfc1918
What do you do when nmap is not available and you want to see the hosts responding to an icmp echo request ? This one-liner will print all hosts responding with their ipv4 address.

Scale,Rotate, brightness, contrast,...with Image Magick
$rotate: the rotate angle $width, $height: width and height to scale to $birghtness: change brighness

Press Any Key to Continue

SoX recording audio and trimming silence
Records audio from your mic in FLAC (Free Lossless Audio Codec) format, starts only after it detects at least 0.1 seconds of noise and stops after 1 second of silence. You can adjust the percent values (sensitivity) to best fit your microphone and voice (0.1% if you have a great quality mic, higher if you don't, 0% does not trim anything). Useful for speech recognition in conjunction with my previous command titled 'Google voice recognition "API"' (http://www.commandlinefu.com/commands/view/8043/google-voice-recognition-api).

change up n directories
Change n directories up, without parameters change one up

Create a mirror of a local folder, on a remote server
Create a exact mirror of the local folder "/root/files", on remote server 'remote_server' using SSH command (listening on port 22) (all files & folders on destination server/folder will be deleted)

Route outbound SMTP connections through a addtional IP address rather than your primary

Convert CSV to JSON
Replace 'csv_file.csv' with your filename.


Stay in the loop…

Follow the Tweets.

Every new command is wrapped in a tweet and posted to Twitter. Following the stream is a great way of staying abreast of the latest commands. For the more discerning, there are Twitter accounts for commands that get a minimum of 3 and 10 votes - that way only the great commands get tweeted.

» http://twitter.com/commandlinefu
» http://twitter.com/commandlinefu3
» http://twitter.com/commandlinefu10

Subscribe to the feeds.

Use your favourite RSS aggregator to stay in touch with the latest commands. There are feeds mirroring the 3 Twitter streams as well as for virtually every other subset (users, tags, functions,…):

Subscribe to the feed for: