Commands tagged dump-gnash (1)

  • This will dump a raw BGRA pixel stream and WAV which must then be converted to video: ffmpeg -f rawvideo -c:v rawvideo -s 1280x720 -r 12 -pix_fmt bgra -i "${i%.*}".bgra -c:v libx264 -preset veryslow -qp 0 -movflags +faststart -i "${i%.*}".wav -c:a libfdk_aac -b:a 384k "${i%.*}".mp4 ; rm "${i%.*}".bgra "${i%.*}".wav Our example generates an x264/720p/12fps/AAC best-quality MP4. To get dump-gnash, first install the build-dependencies for gnash (this step is OS-specific). Then: git clone http://git.savannah.gnu.org/r/gnash.git ; cd gnash ; ./autogen.sh ; ./configure --enable-renderer=agg --enable-gui=dump --disable-menus --enable-media=ffmpeg --disable-jemalloc ; make


    0
    i=in.swf; dump-gnash -1 -j 1280 -k 720 -D "${i%.*}".bgra@12 -A "${i%.*}".wav "${i}"
    mhs · 2015-05-06 23:52:39 2

What's this?

commandlinefu.com is the place to record those command-line gems that you return to again and again. That way others can gain from your CLI wisdom and you from theirs too. All commands can be commented on, discussed and voted up or down.

Share Your Commands


Check These Out

ignore .DS_Store forever in GIT
With a couple of little commands, you?ll be able to ignore the .DS_Store files forever from your git repositories on mac! The following command will add the .gitignore file to the git configuration git config --global core.excludesfile ~/.gitignore then, the following, will add the .DS_Store to the list echo .DS_Store >> ~/.gitignore

Show all configured ipv4
Short list of all ip. Shows even the newly supported multiple ip address on the same interface (see eth1). For ipv6 use -6

Grab an interface's IP from ifconfig without screen clutter
Sometimes, you don't really care about all the other information that ifconfig spits at you (however useful it may otherwise be). You just want an IP. This strips out all the crap and gives you exactly what you want.

Extract IPv4 addressess from file

Get AWS temporary credentials ready to export based on a MFA virtual appliance
You might want to secure your AWS operations requiring to use a MFA token. But then to use API or tools, you need to pass credentials generated with a MFA token. This commands asks you for the MFA code and retrieves these credentials using AWS Cli. To print the exports, you can use: `awk '{ print "export AWS_ACCESS_KEY_ID=\"" $1 "\"\n" "export AWS_SECRET_ACCESS_KEY=\"" $2 "\"\n" "export AWS_SESSION_TOKEN=\"" $3 "\"" }'` You must adapt the command line to include: * $MFA_IDis ARN of the virtual MFA or serial number of the physical one * TTL for the credentials

easily find megabyte eating files or directories

for all who don't have the watch command

Which processes are listening on a specific port (e.g. port 80)
swap out "80" for your port of interest. Can use port number or named ports e.g. "http"

Show simple disk IO table using snmp
Show a simple table with disk IO for the specified host. you monitor a LOT of different thing. Mostly used for MRTG and similar, but this is nice for a quick look, which disk is busy. "public" is your SNMP community ensure that snmpd is running on the host which you intend to monitor

Insert commas to make reading numbers easier in the output of ls
This modifies the output of ls so that the file size has commas every three digits. It makes room for the commas by destructively eating any characters to the left of the size, which is probably okay since that's just the "group".   Note that I did not write this, I merely cleaned it up and shortened it with extended regular expressions. The original shell script, entitled "sl", came with this description:    : '  : For tired eyes (sigh), do an ls -lF plus whatever other flags you give  : but expand the file size with commas every 3 digits. Really helps me  : distinguish megabytes from hundreds of kbytes...  :  : Corey Satten, corey@cac.washington.edu, 11/8/89  : '   Of course, some may suggest that fancy new "human friendly" options, like "ls -Shrl", have made Corey's script obsolete. They are probably right. Yet, at times, still I find it handy. The new-fangled "human-readable" numbers can be annoying when I have to glance at the letter at the end to figure out what order of magnitude is even being talked about. (There's a big difference between 386M and 386P!). But with this nifty script, the number itself acts like a histogram, a quick visual indicator of "bigness" for tired eyes. :-)


Stay in the loop…

Follow the Tweets.

Every new command is wrapped in a tweet and posted to Twitter. Following the stream is a great way of staying abreast of the latest commands. For the more discerning, there are Twitter accounts for commands that get a minimum of 3 and 10 votes - that way only the great commands get tweeted.

» http://twitter.com/commandlinefu
» http://twitter.com/commandlinefu3
» http://twitter.com/commandlinefu10

Subscribe to the feeds.

Use your favourite RSS aggregator to stay in touch with the latest commands. There are feeds mirroring the 3 Twitter streams as well as for virtually every other subset (users, tags, functions,…):

Subscribe to the feed for: