video volume boost

ffmpeg -i input.ogv -vol $((256*4)) -vcodec copy output.ogv

1
By: kev
2012-05-06 03:41:42

These Might Interest You

  • This command sets the volume for the main PulseAudio "sink" (usually the ALSA output interface) to the maximum, 100% (the 0x10000 in the command). To set it to an arbitrary volume, replace 10000 with the volume you want times 100 (so 75% becomes 7500).


    0
    pacmd set-sink-volume 0 0x10000
    andycandet · 2012-07-17 15:02:56 0
  • This normalizes volume in your mp3 library, but uses mp3gain's "album" mode. This applies a gain change to all files from each directory (which are presumed to be from the same album) - so their volume relative to one another is changed, while the average album volume is normalized. This is done because if one track from an album is quieter or louder than the others, it was probably meant to be that way.


    2
    find . -type f -name '*.mp3' -execdir mp3gain -a '{}' +
    Mikelifeguard · 2010-03-21 22:23:44 0
  • This should automatically mount it to /media/truecrypt1. Further mounts will go to /media/truecrypt2, and so on. You shouldn't need sudo/su if your permissions are right. I alias tru='truecrypt' since tr and true are commands. To explicitly create a mount point do: tru volume.tc /media/foo To make sure an GUI explorer window (nautilus, et al) opens on the mounted volume, add: --explorer To see what you currently have mounted do: tru -l To dismount a volume do: tru -d volume.tc. To dismount all mounted volumes at once do: tru -d Tested with Truecrypt v6.3a / Ubuntu 9.10


    2
    truecrypt volume.tc
    rkulla · 2010-04-14 18:34:09 0
  • The lspv command displays the information about the physical volume if the specific physical volume name is specified. If you do not add flags to the lspv command, by default all the available physical volumes are printed along with the following information: * Physical disk name. * Physical volume identifiers (PVIDs). * The volume group, if any, that the physical volume belongs to or the label,if any, locked with the lkdev command. * The state of the volume group. Active-When the volume group is varied on. Concurrent-When the volume group is varied on in the concurrent mode. Locked-When the physical volume is locked with the lkdev command. **************************************************************************************** In the example, the iw406 system has two hard disks. Phy disk name Phy vol identfrs (PVIDs) volume group State of Volumne group hdisk0 00f6267c8a99c7b6 rootvg active hdisk1 00f6267cb3746d01 appinstvg active hdisk0 is mounted on volume group rootvg. hdisk1 is mounted on volume group appinstvg Show Sample Output


    -3
    lspv
    kaushalmehra · 2012-09-13 15:20:06 0

What do you think?

Any thoughts on this command? Does it work on your machine? Can you do the same thing with only 14 characters?

You must be signed in to comment.

What's this?

commandlinefu.com is the place to record those command-line gems that you return to again and again. That way others can gain from your CLI wisdom and you from theirs too. All commands can be commented on, discussed and voted up or down.

Share Your Commands



Stay in the loop…

Follow the Tweets.

Every new command is wrapped in a tweet and posted to Twitter. Following the stream is a great way of staying abreast of the latest commands. For the more discerning, there are Twitter accounts for commands that get a minimum of 3 and 10 votes - that way only the great commands get tweeted.

» http://twitter.com/commandlinefu
» http://twitter.com/commandlinefu3
» http://twitter.com/commandlinefu10

Subscribe to the feeds.

Use your favourite RSS aggregator to stay in touch with the latest commands. There are feeds mirroring the 3 Twitter streams as well as for virtually every other subset (users, tags, functions,…):

Subscribe to the feed for: