lvextend -l +100%FREE /dev/VolGroup00/LogVol00

Extend a logical volume to use up all the free space in a volume group


8
2010-02-09 07:06:54

These Might Interest You

  • The lspv command displays the information about the physical volume if the specific physical volume name is specified. If you do not add flags to the lspv command, by default all the available physical volumes are printed along with the following information: * Physical disk name. * Physical volume identifiers (PVIDs). * The volume group, if any, that the physical volume belongs to or the label,if any, locked with the lkdev command. * The state of the volume group. Active-When the volume group is varied on. Concurrent-When the volume group is varied on in the concurrent mode. Locked-When the physical volume is locked with the lkdev command. **************************************************************************************** In the example, the iw406 system has two hard disks. Phy disk name Phy vol identfrs (PVIDs) volume group State of Volumne group hdisk0 00f6267c8a99c7b6 rootvg active hdisk1 00f6267cb3746d01 appinstvg active hdisk0 is mounted on volume group rootvg. hdisk1 is mounted on volume group appinstvg Show Sample Output


    -3
    lspv
    kaushalmehra · 2012-09-13 15:20:06 0
  • this command extends your logical volume. then it does a resize2fs on it as well. added the -r switch to make it launch resize. Show Sample Output


    2
    lvextend -r -L+100G /dev/VG/LV
    bbelt16ag · 2013-04-20 14:29:11 3

  • 0
    df -kh /dev/vg0*/lv*
    marousan · 2010-02-03 13:37:30 1
  • This command sets the volume for the main PulseAudio "sink" (usually the ALSA output interface) to the maximum, 100% (the 0x10000 in the command). To set it to an arbitrary volume, replace 10000 with the volume you want times 100 (so 75% becomes 7500).


    0
    pacmd set-sink-volume 0 0x10000
    andycandet · 2012-07-17 15:02:56 0
  • This is an easy way to quickly get a status for a device in multipath on SLES systems, as long as the server is configured based on Novell's standards, where multipathed disks are referred to by /dev/disk/by-... tree. Make sure to replace name_of_vg with your Volume Group name.


    -1
    pvscan | awk '/name_of_vg/ {print $2}' | sed 's/[-|/|]/ /g' | cut -d " " -f7
    slashdot · 2010-06-22 16:34:42 0
  • This normalizes volume in your mp3 library, but uses mp3gain's "album" mode. This applies a gain change to all files from each directory (which are presumed to be from the same album) - so their volume relative to one another is changed, while the average album volume is normalized. This is done because if one track from an album is quieter or louder than the others, it was probably meant to be that way.


    2
    find . -type f -name '*.mp3' -execdir mp3gain -a '{}' +
    Mikelifeguard · 2010-03-21 22:23:44 0

What do you think?

Any thoughts on this command? Does it work on your machine? Can you do the same thing with only 14 characters?

You must be signed in to comment.

What's this?

commandlinefu.com is the place to record those command-line gems that you return to again and again. That way others can gain from your CLI wisdom and you from theirs too. All commands can be commented on, discussed and voted up or down.

Share Your Commands



Stay in the loop…

Follow the Tweets.

Every new command is wrapped in a tweet and posted to Twitter. Following the stream is a great way of staying abreast of the latest commands. For the more discerning, there are Twitter accounts for commands that get a minimum of 3 and 10 votes - that way only the great commands get tweeted.

» http://twitter.com/commandlinefu
» http://twitter.com/commandlinefu3
» http://twitter.com/commandlinefu10

Subscribe to the feeds.

Use your favourite RSS aggregator to stay in touch with the latest commands. There are feeds mirroring the 3 Twitter streams as well as for virtually every other subset (users, tags, functions,…):

Subscribe to the feed for: