e2fsck -C -v /dev/device

check the filesystem and use a progress bar

if you happen to start with out the -C switch then you a killall -USR1 e2fsck

2
By: bbelt16ag
2011-04-08 05:33:39

These Might Interest You

  • Nothing fancy, just a regular filesystem scan that calls the badblocks program and shows some progress info. The used options are: -c ? check for bad sectors with badblocks program -D ? optimize directories if possible -f ? force check, even if filesystem seems clean -t ? print timing stats (use -tt for more) -y ? assume answer ?yes? to all questions -C 0 ? print progress info to stdout /dev/sdxx ? the partition to check, (e.g. /dev/sda1 for first partition on first hard disk) NOTE: Never run fsck on a mounted partition!


    10
    fsck.ext4 -cDfty -C 0 /dev/sdxx
    mtron · 2011-05-18 13:13:29 0
  • # AllInOne: Update what packages are available, upgrade to new versions, remove unneeded packages # (some are no longer needed, replaced by the ones from ap upgrade), check for dependencies # and clean local cached packages (saved on disk but not installed?,some are needed? [this only cleans unneeded unlike ap clean]). # aliases (copy into ~/.bashrc file): alias a='alias' a ap='apt-get' a r='ap autoremove -y' a up='ap update' a u='up && ap upgrade -y --show-progress && r && ap check && ap autoclean' # && means "and run if the previous succeeded", you can change it to ; to "run even if previous failed". I'm not sure if ap check should be before or after ap upgrade -y, you can also change the alias names. # To expand aliases in bash use ctrl alt e or see this ow.ly/zBKHs # For more useful aliases go to ow.ly/zBMOx


    0
    apt-get update && apt-get dist-upgrade -y --show-progress && apt-get autoremove -y && apt-get check && apt-get autoclean -y
    unixmonkey78577 · 2014-07-26 12:18:57 0
  • -r for recursive (if you want to copy entire directories) src for the source file (or wildcards) dst for the destination --progress to show a progress bar


    10
    rsync -rv <src> <dst> --progress
    fecub · 2011-08-05 09:29:12 4
  • Knowing when a filesystem is created , you can deduce when an operating system was installed . find filesystem device (/dev/) informations by using the cat /etc/fstab command. Show Sample Output


    7
    dumpe2fs -h /dev/DEVICE | grep 'created'
    eastwind · 2009-12-12 14:47:33 2
  • Opens a snapshot of a live UFS2 filesystem, runs dump to generate a full filesystem backup which is run through gzip. The filesystem must support snapshots and have a .snap directory in the filesystem root. To restore the backup, one can do zcat /path/to/adXsYz.dump.gz | restore -rf -


    2
    dump -0Lauf - /dev/adXsYz | gzip > /path/to/adXsYz.dump.gz
    tensorpudding · 2010-07-19 00:54:40 2
  • Stops when the (last) dd process exits.


    -2
    while killall -USR1 dd; do sleep 5; done
    Mikachu · 2009-11-09 00:27:33 0

What Others Think

Invalid non-numeric argument to -C ("-v")
netizen · 370 weeks and 6 days ago
e2fsck -f -C 0 /dev/mapper/THRACE--SHARES-movies
bbelt16ag · 359 weeks and 5 days ago
yeah i just figured that out it depends on the version
bbelt16ag · 359 weeks and 5 days ago

What do you think?

Any thoughts on this command? Does it work on your machine? Can you do the same thing with only 14 characters?

You must be signed in to comment.

What's this?

commandlinefu.com is the place to record those command-line gems that you return to again and again. That way others can gain from your CLI wisdom and you from theirs too. All commands can be commented on, discussed and voted up or down.

Share Your Commands



Stay in the loop…

Follow the Tweets.

Every new command is wrapped in a tweet and posted to Twitter. Following the stream is a great way of staying abreast of the latest commands. For the more discerning, there are Twitter accounts for commands that get a minimum of 3 and 10 votes - that way only the great commands get tweeted.

» http://twitter.com/commandlinefu
» http://twitter.com/commandlinefu3
» http://twitter.com/commandlinefu10

Subscribe to the feeds.

Use your favourite RSS aggregator to stay in touch with the latest commands. There are feeds mirroring the 3 Twitter streams as well as for virtually every other subset (users, tags, functions,…):

Subscribe to the feed for: