Fetches the world population JSON data from the US census and parses it uses jshon

I actually planned to do this for quite a long time, but since I haven't had any suitable client hardware, I procrastinated this. Now, the old laptop I've got from my dad, features an RS-232 port. So, now that I had technically a client, that I could test my RS-232 connection with, I ordered a null modem cable. There is no RS-232 outlet on my desktop computer directly on the mainboard, but theres a connector on the mainbord, where a RS-232 outlet can be attached to. The outlet will then cover up a PCI slot. # Activating RS-232 Ok, once all cables were in place, I tried to access both RS-232 ports by reading from them directly. They're usually ttyS0 or ttyS1, depending what COM-Port it is. From the file /proc/tty/driver/serial, information about the serial setup can be obtained. A setserial -q /dev/ttyS0 might be usefull as well. Usually, the UART Type is 16550A, on a standard PC. Mine wasn't working though. At leas not right from the start, when I tried to read the interface with cat /dev/ttyS0 I got the following error: # cat /dev/ttyS0 cat: /dev/ttyS0: Input/output error Obviously, the driver couldn't activate the hardware. Reason was, it was deactivated in BIOS. After activating RS-232 there, it worked well. As a last action, I added myself to the uucp group, so I have user permission to the serial lines. It is not necessary for the terminal setup, but a good idea to do so, just for future projects, maybe... # Setting up a terminal Once the Serial line is configured and working properly, it's time to let a terminal run on that port. This is what I added to my /etc/inittab : s0:2345:respawn:/sbin/agetty -L 38400 ttyS0 I added it quite on the top of that file, right below the 'si' statement, mingetty cannot be used for serial connections, it cannot be run in a console, too. I tried it for testing purposes, but the cosole - along with your login program - will log you out, as soon as you log in over your serial line. '-L' means this is a local line, with no carrier signal. 38400 is the standard speed of a Linux console, it might be a bit high, I was told, but it works well. I tested that with some higher values as well (115200) and it worked too, I guess it tepends on things like cable length, etc. Last parameter, is the serial tty to listen on. The terminal type can be specified as an additional parameter at the end of the parameter list, vt102, for instance. This is sometimes required, depending on the client. After finishing editing /etc/inittab, an init q will make the system re-read /etc/inittab and apply changes. The agetty should now be listening on ttyS0. #Setting up a client It's time to establish a connection and test the serial line. I use a laptop, that has an RS-232 port, so some preliminary setup is required. I tried minicom as terminal initially, but it turned out, not to be the best client. It initializes the modem, this lasts quite long, and it doesn't convey ANSI colors. So the better option is cu, it's part of the UUCP-Package. Oh, and the serial port of that computer, has to be accessible as well, of course. Once everything was set up, I established the connection: $ cu -l ttyS0 -38400 --nostop Pretty self explanatory, I think. The --nostop option disables XON/XOFF handling. # root access over ttyS0 In order to become root over the serial terminal, the tty needs to be added to /etc/securetty I appended ttyS0 to the end of the file. It is now possible, to gain root access over the serial terminal. The agetty process needs to be restarted to apply changes. # Accessing GRUB over ttyS0 To make bootloader access possible over ttyS0, some changes to /boot/grub/menu.lst need to be done. (GRUB is the bootloader I use, I suppose LiLo has similar capabilities.) Those are the lines, I appended to the top of my menu.lst : serial --unit=0 --speed=38400 --word=8 --parity=no --stop=1 terminal --timeout=3 serial console The serial command initiates the serial terminal option, --unit=0 defines our first serial connector, I my case, it's the only one I have on my machine. I used the standard Linux-Console speed, as well as the "8N1" connection strategy. terminal defines the terminal priorities, first terminal (serial) is the standard one, the last one is the secondary terminal (console). --timeout=3 enables a delay on both consoles, with a prompt for a keystroke. Depending on which terminal, the key is pressed, this terminal, will be used. If no key is pressed after the timeout, the standard console (in my case serial) will be used. # Relaying Kernel output on boot The Kernel accepts multiple console options, of which the last one, is the standard console, and the one that will be used in Single User mode. These are my Kernel options: title Fedora Core (2.6.20-1.2316.fc5) root (hd0,0) kernel /vmlinuz-2.6.20-1.2316.fc5 ro root=/dev/VolGroup00/LogVol00 rhgb quiet vga=795 console=tty0 console=ttyS0,38400 initrd /initrd-2.6.20-1.2316.fc5.img console=tty0 is the standard console, located on the machine, i.e. monitor and keyboard.

This is super fast and an easy way to test your terminal for 256 color support. Unlike alot of info about changing colors in the terminal, this uses the ncurses termcap/terminfo database to determine the escape codes used to generate the colors for a specific TERM. That means you can switch your terminal and then run this to check the real output. $ tset xterm-256color at any rate that is some super lean code! Here it is in function form to stick in your .bash_profile aa_256 () { ( x=`tput op` y=`printf %$((${COLUMNS}-6))s`; for i in {0..256}; do o=00$i; echo -e ${o:${#o}-3:3} `tput setaf $i;tput setab $i`${y// /=}$x; done ) } From my bash_profile: http://www.askapache.com/linux-unix/bash_profile-functions-advanced-shell.html

Bash snippet to force GNU/Linux keyboard settings, layout and configuration. Usefull when some GNU/Linux distributions such as *Ubuntu's store only limited configation options due to demonstration purposes on LiveUSB or Live persistent devices. Overcomes the English QWERTY to French AZERTY settings failure. Code bash en ligne de commande pour forcer l'adoption du clavier AZERTY sur les cl? USB bootable en Ubuntu.

cat file1 file2 file3|sort|uniq -d finds the same lines in several files, especially in files with lists of files.

No curl and no sed, just wget :)

I have a remote php file that I want to run once an hour. I set up cron to run this wget. I don't really care about what's in the file though, I don't want to save the results, so I run the -O and send it to /dev/null